Coilover, Factory Vogtland BMW 1er F20, F21 (1K2,1K4) 2WD 968710. The description of this item has been automatically translated. Suitable for the following vehicles. Vehicle: BMW 1 Series F20, F21 2WD Type: 1K2, 1K4 114i, 114d, 116i, 1116d, 118i, 118d, 120d Construction year: from 09.11 -> Lowering: VA: approx. 30-55 mm, HA: approx. Axle loads: VA: up to 920 kg, HA: 1160 kg Notes: 15, 24, 62. Are you not sure whether the chassis fits your vehicle? The coilover suspension from VOGTLAND offers individual lowering with a sporty preset Damper characteristics. This quality product only uses special high-performance 2-pipe dampers used with a low gas pressure system and first-class corrosion protection. In conjunction with the individual housing length tailored to your vehicle type, Make full use of the available spring travel for your own personal depth adjustment. And all of this in the tested area. You don’t even have to forego the required remaining spring travel. The sporty, comfortable set-up enables top road holding and excellent driving characteristics. Depending on the vehicle brand, the permitted adjustment range is up to 80 mm and guarantees a sporty look. 2-pipe gas pressure damper. The amount of lowering is reduced by the amount of the factory lowering. The measure of the lowering will be reduced by the measure of the sport suspension. Wedge shape: The lowering of the front axle depends on the equipment and engine variant. Wedge form: The lowering of the front axle depends on the equipment and weight of the engine. From chassis number 21234. As of chassis number: 21234. For fine-tuning, please use Mercedes-Benz spring plate pads, which are available in different thicknesses (8 – 23 mm). For fine tuning, please refer to the Daimler Benz spring insolators available in different heights (8-23 mm). Reinforced version (heavy duty) for vehicles with full equipment and more than 4 cylinders. Heavy duty for models with full equipment and more than 4 cylinders. For vehicles with a load-dependent brake force distributor, a demonstration is required despite ABE. A presentation is necessary despite ABE for vehicles with a load depending brake power distributor. Not for vehicles with level control/air suspension. Without self-leveling / air suspension. For vehicles with Tiptronic, Multitronic, increased lowering possible. Additional lowering may occur on vehicles equipped with automatic transmissions. Only for vehicles with full equipment. With the XR3i there is no additional lowering, just tighter tuning. XR3i does not lower, only the adjustment becomes more sportive. For vehicles with 6 cylinders, e. Golf III VR6, it is recommended to convert to sports dampers, included in the VOGTLAND complete chassis. Vehicles with 6 cylinder engines require sport shocks. Not for: Break, Caravan, Tournament, T-model, Touring, Variant, Avant, Station Wagon, Traveler, (estate). Not for station wagons. As of ABE number 9138/2. Use spring plate with the number: 171412341A up to 8.79. Up to 8.79 please use spring cap number 171412341A. Not for all-wheel drive. Excludes 4 wheel drive. Modified spring plates [and possibly other parts] must be used on the front axle. Either the spring plate with the VW part number 1H0412341 (large) or 357412341 A (small). Volkswagen springs caps [and probably further Parts] might be necessary:?? 1H0412341 (big) or 357412341 A (small). Shortened sports shock absorbers required. These are already included in the VOGTLAND complete chassis. Shorter sport shocks are required. The VOGTLAND suspension kits are covered with these shocks. Not for series sports suspensions. Not suitable for serial or sport suspension. Only front axle springs, rear axle torsion bars (or standard spring element). Only front springs, torsion bars (or standard spring) on?? the rear axle. Rear axle springs only, front axle torsion bars (or standard spring element). Only rear springs, torsion bars (or standard spring) on?? the front axle. All wheel/tire combinations approved by the wheel testing centers can be used. The requirements in the wheel report or Wheel ABE must be adhered to, with the exception of the requirement for standard chassis. All wheel/tire combinations are allowed which are released by the wheel type testing institution. The conditions in the wheel approval have to be kept, except when suspension is required. With adjustable complete chassis, the damping forces can only be adjusted on the front axle when installed. At the VOGTLAND adjustable suspension kits only the shock valvings in the front are adjustable. Due to vehicle-specific tolerances, it may be possible that the stabilizer bar and drive shaft come into contact. For coilover kit: Item no. 968550000, stabilizer kit, without xenon. For complete chassis: elongated standard coupling rods (VW/Audi). Due to vehicle-specific tolerances a contact between the drive shaft and the anti-roll bar might occur. In such case it is required to install a modified anti-roll bar. For Coilover Sets use Order No. 968 550 000 (Anti-roll bar conversion set without Xenon headlights). For Suspension Kits use a longer steering rod from your VW/Audi dealer. VA/HA threaded spring struts (height adjustable). Height adjustable at the front and rear axle (threaded strut housings). VA/HA height adjustable VA threaded spring struts, RA springs with height adjustment plus. Height adjustable at the front and rear axle (front axle threaded housings, rear axle threaded spring perch and separate shocks). Only VA height adjustable, HA spring and shock absorber. Only height adjustable at the front axle (threaded strut housings), springs and shocks at the rear axle. Possibly with standard tires. May require the use of wheel spacers with equipment tires and wheels. The level control must be shut down. Self-leveling must be shut down. VA height-adjustable threaded spring strut, RA sports shock absorber (adjustment of the rear using a torsion bar). Height adjustable at the front (threaded strut housings), rear axle is adjustable with torsion spring adjustment. Damper adjustable when installed. Installed shocks can be adjusted when installed. Damper can only be adjusted when removed. Installed shocks cannot be adjusted when installed. The front direction indicators (§ 76/756 EC) must maintain a minimum height of 350 mm. Alfa part number: 46226968. The front turn lights (§76/756 EG), must be the min. Height from 350 mm. Production date 4/02 (piston rod thread visible), from 4/02 (piston rod thread covered). For vehicles manufactured before 04/02, the piston rod is fastened to the support bearing with an arched disk (piston rod threads visible). Models built after 04/02, piston rod threads not visible. Use only for vehicles with rear shock absorber mount M10 (1.0i, 1.2i, 1.7Di). Only for vehicles which have rear dampers mounted below with M10 (1.0i, 1.2i, 1.7Di). Use only for vehicles with rear shock absorber mount M14. (1.4i, 1.8i, 1.3CDTI, 1.7DTi, 1.7CDTi). Only for vehicles which have rear dampers mounted below with M14 (1.4i, 1.8i, 1.3CDTI, 1.7DTi, 1.7CDTi). VA shock absorber: complete shock absorber for item no. 960422, 960423, 966322, 966404, 966406, 966407, 969419, 969422, 969423, 960462. Front shock: complete suspension strut. Part number: 966404, 966406, 966407, 966322, 960422, 969423, 960423, 960462. VA shock absorber: strut cartridge. Dampers are only suitable for European vehicles. Damper only suitable for European cars. With a drive shaft diameter of more than 42. Tested lowering by approx. If the driveshaft diameter is greater than 42, mm the max. Approved lowering is reduced 15 mm. The internal distance on the front shock absorber (between the fastening straps) must be 27 mm. The inside distance between the mounting bracket of the front damper must be 27 mm. From chassis number Y-on the 10th Job. From chassis number Y on the 10th position. For vehicles with 50 mm shock absorbers. For cars with 50 mm suspension strut. For vehicles with 55 mm shock absorbers. For cars with 55 mm suspension strut. For vehicles built between 10.91 and 5.92, the upper mounting bearings BMW no. 31331090467 must be used. For cars built from October 1991 up to May 1992 the upper attachment must be replaced by BMW part number 31.331.090.467. Until 1998 (up to chassis number 8DX199999). Up to 1998 models (up to VIN: 8DX199999). Coupling rods 968220, 968221 required for lowering over 40 mm. Steering rod 968220, 968221 for lowering above 40mm nessecary. After the chassis has been installed, there is freedom of movement Check the tires on the VA shock absorber min. 5 mm and if necessary. By means of using tested spacers. After mounting the clearance between Wheel and Suspension Strut must be at least 5mm. If it is smaller you have to use wheel spacers. Audi: Year of manufacture up to 4.00, VW: Year of manufacture up to 9.99. Audi: Model year up to 4.00, VW: Model year up to 9.99. Audi: Year of manufacture from 5.00, VW: Year of manufacture from 10.99. Audi: Model year after 5.00, VW: Model year after 10.99. Without 16V, VA mounting hole distance 52 mm. Without 16V, front bracket bolt distance 52 mm. Without 16V, VA mounting hole distance 54 mm. Without 16V, front bracket bolt distance 54 mm. Without Rallye, TD, Genty, CT, CTI, GTI. Year of manufacture up to 8.04, without 2.0T, 3.0V6 CDTi, without IDS. Model year up to 08.04, without 2.0T, 3.0V6 CDTI, without IDS. From year 8.04, without 2.0T, 3.0V6 CDTi, without IDS. Model year after 08.04, without 2.0T, 3.0V6 CDTI, without IDS. For vehicles with eyes attached to the HA. For models with eye mounting at the rear. For vehicles with fork attachment on the rear. For models with fork mounting at the rear. Not for vehicles from model year 2004. Not for models built after 2004. VA shock absorber, check the dimensions of the fastening brackets: hole spacing 52 mm; Distance 23 mm. On front shock check measurements for the bracket: inside width 23 mm, mounting hole distance 52 mm. Only for four-wheel drive (4WD) vehicles. Only for cars with four wheel drive (4WD). VA also 8 cyl. Engine BMW part no. Dome bearing 31331091709, washer 31331116983, sleeve 31331110196, rear BMW part no. Support bearing 33521091710, support pot 33521090282, washer 33521092986, protective tube 31331137 93 2, Elastomers 33531091031. Additional OE equipment is needed on cars with EDC. Engines BMW part number: Bearing 31331091709, Washer 31331116983, Dust Cap 31331110196. Rear BMW part number: Bearing 33521091710, 33521090282, Washer 33521092986, Dustseal 31331137 932, Bumpstop 33531091031. Sports damper (included) in conjunction with standard air spring on the rear. The OE air suspension is not removed. A rear sport shock is provided and used with the air suspension. Not for vehicles with electronic damper adjustment. Not for vehicles with electronic damping adjustment. For Allen vehicles before year of manufacture. 6/92, fundamentally modified dome bearings must be used. Dome bearing 31336764947, washer 31331116983, sleeve 31331110196. For all cars built before 6/92 the use of different top bearing assembly in the front is required. BMW part number: Bearing 31336764947, Washer 31331116983, Dustseal 31331110196. Without electrical Damping force regulation, without IDS+. Damping force adjustment, without IDS+. Audi part number: shock absorber bearing 8E0512121E, spring pad 8E0512149H, stop buffer 4B0512131Q. For cars with self-leveling additional OE parts are required: Audi Part number: Bearing 8E0512121E, Springseat 8E0512149H, Bump stop 4B0512131Q. Vehicle-specific connection plug included. Model specific plug&play adapter included. Hardness adjustment only on the VA. Model specific plug&play adapter available as option. Only for vehicles with air suspension. Only for cars with air suspension. Only for vehicles with ABC chassis. Only for cars with ABC suspension. From chassis number: Turbo: 4LA83740, S: 4LA48416, V6: 4LA01526, USA Turbo: 4LA93466, USA S: 4LA6&74337, USA V6: 4LA21527. From VIN: Turbo: 4LA83740, S: 4LA48416, V6: 4LA01526, USA Turbo: 4LA93466, USA S: 4LA6&74337, USA V6: 4LA21527. Only for multi-link rear axle. Only for Multilink rear suspension. Only for torsion beam rear axle. Only for twist-beam rear suspension. For vehicles with an individual operating license (EBE), an acceptance test in accordance with §21 StvZo (individual acceptance) is required. Sets without available as export items. For cars with a single operating permit (EBE) an approval regarding §21 StvZo is required. Sets without can be ordered for export market. In preparation, please inquire. In development, please call. Notes in brackets only apply to complete chassis. Remarks in brackets only for kits. We reserve the right to make technical changes. We assume no liability for printing errors. Subject to possible technical revisions. Reserves the right to change product specifications. We do not assume liability for misprinting. I ask for your understanding! If you have any questions, we will be happy to help you. Monday to Thursday: 8 a. M Friday: 8 a. The free setting tool. List your items quickly and conveniently and manage your active offers. Engines BMW part number: Bearing 3133109170.